Layer 2 full Gigabit modular managed Ethernet switch with 4 fixed 10GbE SFP+ slots, 2 slots for optional 4-port GE/FE modules, 2 slots for isolated power modules, up to 8 Gigabit Ethernet ports, -40 to 75°C operating temperature
Ethernet Interface
-
Pre-installed Modules
- 4 embedded 10Gigabit ports
-
Module
- 2 slots for optional 4-port FE/GE modules
-
Slot Combination
- See the LM-7000H module series datasheet for more information.
Note: The required power module depends on the choice of LM-7000H module. Refer to the following power/module combination requirements.
LM-7000H non-PoE modules:
Any power module
LM-7000H PoE modules:
PWR-HV-P48-A, PWR-LV-P48-A only
-
Standards
- IEEE 802.3 for 10BaseT
IEEE 802.3u for 100BaseT(X) and 100BaseFX
IEEE 802.3ab for 1000BaseT(X)
IEEE 802.3z for 1000BaseX
IEEE 802.3x for flow control
IEEE 802.3ad for Port Trunk with LACP
IEEE 802.1Q for VLAN Tagging
IEEE 802.1D-2004 for Spanning Tree Protocol
IEEE 802.1w for Rapid Spanning Tree Protocol
IEEE 802.1p for Class of Service
IEEE 802.1X for authentication
Ethernet Software Features
-
Management
- IPv4/IPv6
Flow control
Back Pressure Flow Control
DHCP Server/Client
ARP
DHCP Relay Agent (Option 82)
Fiber check
RARP
LLDP
Linkup Delay
Port Mirroring (SPAN, RSPAN)
SMTP
SNMP Trap
SNMP Inform
SNMPv1/v2c/v3
RMON
TFTP
SFTP
HTTP
HTTPS
Telnet
Syslog
Private MIB
-
Filter
- GMRP
GVRP
GARP
802.1Q VLAN
IGMP Snooping v1/v2/v3
IGMP Querier
-
Redundancy Protocols
- STP
RSTP
Turbo Ring v2
Turbo Chain
Ring Coupling
Dual-Homing
Link Aggregation
MRP
MSTP
Network Loop Protection
-
Security
- Broadcast storm protection
DHCP Snooping
Dynamic ARP Inspection
IP Source Guard
Rate Limit
Trust access control
Static Port Lock
MAC Sticky
HTTPS/SSL
SSH
RADIUS
TACACS+
Login and Password Policy
Secure Boot
MAC Authentication Bypass
Access control list
-
Time Management
- SNTP
IEEE 1588v2 PTP (hardware-based)
Supported power profiles: IEEE 1588 Default 2008, IEC 61850-9-3-2016, IEEE C37.238-2017
NTP Server/Client
NTP Authentication
-
Protocols
- IPv4/IPv6
TCP/IP
UDP
ICMP
ARP
RARP
TFTP
DNS
NTP Client
DHCP Server
DHCP Client
802.1X
QoS
HTTPS
HTTP
Telnet
SMTP
SNMPv1/v2c/v3
RMON
Syslog
-
Industrial Protocols
-
MIB
- P-BRIDGE MIB
Q-BRIDGE MIB
IEEE8021-SPANNING-TREE-MIB
IEEE8021-PAE-MIB
IEEE8023-LAG-MIB
LLDP-EXT-DOT1-MIB
LLDP-EXT-DOT3-MIB
SNMPv2-MIB
RMON MIB Groups 1, 2, 3, 9
-
Power Substation
- MMS
1588 PTP Power Profile IEC 61850-9-3
1588 PTP Power Profile C37.238-2017
Switch Properties
-
MAC Table Size
-
Max. No. of VLANs
-
VLAN ID Range
-
IGMP Groups
-
Jumbo Frame Size
-
Priority Queues
-
Packet Buffer Size
LED Interface
-
LED Indicators
- PWR, EPS, STATE, SYNC, FAULT, MSTR/HEAD, CPLR/TAIL
Input/Output Interface
-
Digital Input Channels
-
Digital Inputs
- +13 to +30 V for state 1
-30 to +3 V for state 0
Max. input current: 8 mA
-
Alarm Contact Channels
- 3 (On MGMT, PWR1, PWR2 Module)
Relay output with current carrying capacity of 2 A @ 30 VDC
-
Buttons
Power Parameters
-
Input Voltage
- With PWR-HV-P48–A installed:
110/220 VDC, 110 VAC, 60 HZ, 220 VAC, 50 Hz, PoE: 48 VDC
With PWR-LV-P48–A installed:
24/48 VDC, PoE: 48 VDC
With PWR-HV-NP installed
110/220 VDC, 110 VAC, 60 HZ, 220 VAC, 50 Hz
With PWR-LV-NP installed:
24/48 VDC
-
Operating Voltage
- With PWR-HV-P48–A installed:
88 to 300 VDC, 90 to 264 VAC, 47 to 63 Hz, PoE: 46 to 57 VDC
With PWR-LV-P48–A installed:
18 to 72 VDC, PoE: 46 to 57 VDC
With PWR-HV-NP installed:
88 to 300 VDC, 90 to 264 VAC, 47 to 63 Hz
With PWR-LV-NP installed:
18 to 72 VDC
-
Input Current
- With PWR-HV-P48-A/PWR-HV-NP installed:
Max. 0.38 A @ 110 VDC
Max. 0.20 A @ 220 VDC
Max. 0.75 A @ 110 VAC
Max. 0.48 A @ 220 VAC
With PWR-LV-P48-A/PWR-LV-NP installed:
Max. 1.90 A @ 24 VDC
Max. 0.95 A @ 48 VDC
EPS (PoE models only):
Max. 8.2 A @ 48 VDC
Note: These are the input current ratings for the device with the maximum number of modules installed.
-
Power Consumption (Max.)
- With PWR-HV-P48-A/PWR-HV-NP installed:
Max. 41.8 W @ 110 VDC
Max. 44.2 W @ 220 VDC
Max. 46.6 W @ 110 VAC
Max. 46.5 W @ 220 VAC
With PWR-LV-P48-A/PWR-LV-NP installed:
Max. 45.8 W @ 24 VDC
Max. 45.8 W @ 48 VDC
Note: These are the maximum power consumption ratings for the device with the maximum number of modules installed.
-
Overload Current Protection
-
Reverse Polarity Protection
-
Max. PoE Power Output per Port
-
Total PoE Power Budget
- Max. 360 W (with one power supply) for total PD consumption at 48 VDC input for PoE systems
Max. 360 W (with one power supply) for total PD consumption at 53 to 57 VDC input for PoE+ systems
Max. 720 W (with two power supplies) for total PD consumption at 48 VDC input for PoE systems
Max. 720 W (with two power supplies) for total PD consumption at 53 to 57 VDC input for PoE+ systems
Physical Characteristics
-
IP Rating
-
Dimensions
- 197 x 115 x 163.25 mm (7.76 x 4.53 x 6.43 in)
212 x 115 x 163.25 mm (8.35 x 4.53 x 6.43 in) with dual PWR-HV-P48-A/PWR-LV-P48-A power modules installed
-
Weight
-
Installation
- DIN-rail mounting
Wall mounting (with optional kit)
Rack mounting (with optional kit)
Environmental Limits
-
Operating Temperature
- -40 to 75°C (-40 to 167°F)
-
Storage Temperature (package included)
- -40 to 85°C (-40 to 185°F)
-
Ambient Relative Humidity
- 5 to 95% (non-condensing)
Standards and Certifications
-
Safety
- EN IEC 62368-1
IEC 62368-1
UL 62368-1
IEC 60950-1
UL 61010-2-201
EN 61010-2-201
-
EMC
- EN 55032/35
EN 61000-6-2/-6-4
-
EMI
- CISPR 32, FCC Part 15B Class A
-
EMS
- IEC 61000-4-2 ESD: Contact: 8 kV; Air: 15 kV
IEC 61000-4-3 RS: 80 MHz to 1 GHz: 20 V/m
IEC 61000-4-4 EFT: Power: 4 kV; Signal: 4 kV
IEC 61000-4-5 Surge: Power: 4 kV; Signal: 4 kV
IEC 61000-4-6 CS: 10 V
IEC 61000-4-8 PFMF
IEC 61000-4-11 Voltage Dips & Interruptions
-
Railway
-
Traffic Control
-
Shock
-
Freefall
-
Vibration
-
Power Substation
